Eco Friendly Companies | ECO PRODUCTS | Hardware Products | Battic Door Energy Conservation Products

Eco Friendly Companies | ECO PRODUCTS | Hardware Products | Battic Door Energy Conservation Products | Images/Products

Battic Door Energy Conservation Products
We manufacture and distribute low-cost, high-value, energy conservation products for the FIVE largest intentional openings in the house: Battic Door R-50 Attic Stairs Insulator Covers, Battic Door Who ...	Box 15 Mansfield 02048-0015 Massachusetts USA

	R-50 Attic Stair Cover We are the original - We are the Best! The only stair cover kit available that meets the International Energy Conservation Code - used in all 50 states and most jurisdictions! R-49+ is NOW REQUIRED FOR NEW CONSTRUCTION AND RENOVATION! And only WE have it! "403.2.3 Access hatches and doors. Access doors from conditioned spaces to unconditioned spaces (e.g., attics and crawl spaces) shall be weatherstripped and insulated to a level equivalent to the insulation on the surrounding surfaces. " By reducing the amount of heat and moisture leaking into your attic, the severity of ice dams and attic mold is greatly reduced! Fits the most common size attic stairs - starting at only $29.50 - pays for itself in months! R-50 Kit shown is $99.50 + shipping
	EZ Hatch Attic Access Scuttle Door, 22" x 30" R-42 The EZ Hatch Attic Access Scuttle Door Panel Hatch System is an easy to install, easy to use, highly insulated door, panel, scuttle hatch system that installs in minutes and provides an air sealed, professional, high-quality, insulated access opening into the attic space. Triple gaskets provide an air tight seal! The core of the door is 10" thick and made of Expanded Polystyrene foam that provides a greater R-Value per inch than fiberglass. The face of the door is gloss white, durable, and easy to clean. The top gasket of closed cell insulation seals the top of the door. The gasket is fire rated per ASTM E84 for flame spread (FSI) 25 or less, smoke developed (SDI) 50 or less, (required by Code for exposed insulation) and meets code requirements. The lightweight door weighs 10 pounds, and lifts up and out of the way for easy attic access. No hinges - The door is designed to prevent interference with the roof joists. Triple pre-installed weatherstrip gaskets ensure an air tight seal. Gasketing provided where the trim meets the ceiling, where the face of the door meets the trim, and where the top of the door meets the frame. The lightweight door opens with little effort, allowing easy entry into your attic space. The finished face on the door fits tightly into the weatherstrip on the trim when the door closes. Perfect for use with any type of attic insulation, including blown-in insulation. The 12 in. tall wood frame acts as an insulation dam, which holds the insulation back from the opening, and takes the mess out of getting into your attic space. Sized to fit either between roof trusses 24" on-center, or between ceiling joists 16" o.c. with minimal carpentry required (cut one joist and add headers). Whether in new construction or retrofit, the unit can be installed in minutes with only a utility knife and a screwdriver. Prefinished gloss white trim and door standard. $199 + $29 shipping
	The Fireplace Draftstopper Chimney Plug Balloon The Fireplace Draft Stopper is an inflatable urethane chimney plug balloon pillow measuring 38" x 16". A round Fireplace Plug is also available. It is quickly and easily installed in the fireplace just below the damper level. The Fireplace Plug can be adapted to work in almost all fireplaces. Even if you have an unusual construction, the Fireplace Plug can be successfully installed in less than 2 minutes. The Fireplace Plug is provided with 5 "slittable" areas that can be cut to provide an opening for a damper handle. As the Draftstopper is inflated it seals around the damper handle sealing the opening! Easy, quick and clean installation - does not go up the chimney so no messy soot to deal with! The Large Fireplace Plug Draft Stopper is an inflatable urethane pillow measuring 38" x 16". It is quickly and easily installed in the fireplace just below the damper level. The Draft Stopper can be adapted to work in almost all fireplaces. Even if you have an unusual construction, the Draft Stopper can be successfully installed in less than 2 minutes. The Draftstopper is provided with 5 "slittable" areas that can be cut to provide an opening for a damper handle. As the Draftstopper is inflated it seals around the damper handle sealing the opening! Stop valuable warm air from leaving your home and minizing drafts from your fireplace. Some heating experts claim that an unlit fireplace with a damper open can increase heating costs by as much as 30 percent. Now that could add up to $500 over the course of a season. Well, here's a solution that's relatively inexpensive, easy to install and pretty much invisible.
	Whole House Attic Fan Insulation Shutter Seal Whole House Attic Fan Insulation Shutter Seals and Covers - Also For AC Vents and Returns! The Battic© Door Whole House Attic Fan Ceiling Shutter Seal is an energy-saving insulating seal for Whole House Attic Fans. It reduces air-leakage through the whole house attic fan saving the homeowner heating and cooling loss and energy costs. The Battic© Door Whole House Attic Fan Ceiling Shutter Seal is easily installed over the fan louver from the house side in the fall and removed in the spring. By reducing the amount of heat and moisture leaking into your attic, the severity of ice dams and attic mold is greatly reduced! The Battic Door Whole House Attic Fan Ceiling Shutter Seal is an energy-saving insulating seal for Whole House Attic Fans. It reduces air-leakage through the whole house attic fan saving the homeowner heating and cooling loss and energy costs. The Battic Door Whole House Attic Fan Ceiling Shutter Seal is easily installed over the fan louver from the house side in the fall and removed in the spring. No need to enter the attic to install the kit. By reducing the amount of heat and moisture leaking into your attic, the severity of ice dams and attic mold is greatly reduced! The back of the foam is reflective, reflecting attic heat away from house in summer and reflecting heating back into house in winter. Kits are easy to install. Simply Trim-To-Fit! Each kit includes a supply of white foam (3/16 in., thick R-8) and white Velcro. The flat-white colored foam has a textured finish and blends in with the ceiling. The foam is a solid-core that trims easily with scissors - it cannot unravel and does not have any frayed edges. We even provide white tape to wrap the edges if desired for a "finished-look". May also be used to cover and seal AC Vents and Returns! INSTALLATION INSTRUCTIONS Step 1. Remove release liner from one side of Velcro and install Velcro onto perimeter of shutter. Step 2. Remove release liner from other side of Velcro and install foam into it leaving an overhang on all 4 sides. Step 3. Trim edges with scissors. Leave 1/4 in. of overhang if you wish to wrap edges with tape. INSTALLATION TIPS Do not trim foam before installation. Silver side of foam goes up, white side goes down. When removing cover, separate Velcro at a corner and peel off. For storage place under bed or roll-up. Each kit includes enough Velcro to go around perimeter of foam: 14 ft Velcro with our small 3x4 ft kit, 16 ft Velcro with our medium 4x4 ft kit, 20 ft Velcro with our large 5x4 ft kit. If additional Velcro is desired it may be purchased in 14 ft long strips for $10. PERFECT TO COVER YOUR AC VENTS! Simply add up the amount of materials you need and purchase additional Velcro strips as needed.